Q&A of Spooky2 Online Training Course – Which Kit To Choose

Terrain Protocol

At Spooky2, we always recommend our users run the Terrain Protocol Preset for detoxification before starting their Rife frequency treatment. Because Terrain Protocol was designed for full body detox, it will help your body be ready for Rife frequency treatment.

For more information, you can check the below links:

Q1: Terrain protocol will run 11 days, did you put 11 days manually?

A: If you run the terrain protocol in Remote mode, it loops itself once for 11 days until you manually stop it.

If terrain protocol is run in contact or plasma mode, it will run 2-3 hours a day, and you need to manually restart the subsequent preset the next day.

Q2: After choosing terrain preset, why does it only show 1 h on the control tab?

A: The terrain preset is a preset chain that includes 15 single presets. It will only show the single duration of the first preset on the control tab, however, it will loop 24 hours and go to the next preset automatically.

Q3: How can I resume my Terrain Protocol if my laptop accidentally shuts down?

A: It is always important to note which day you are on when running the Terrain Protocol so that you can start from the step you were at before. Here is a blog that demonstrates how you can resume your Terrain Protocol:
https://www.spooky2-mall.com/blog/how-to-resume-terrain-protocol/ .

Q: Why Do We Recommend Using Multiple Generators?

Answer: Using Rife technology to help with your health condition isn’t a simple case. It is not just a matter of killing pathogen cells. There’s much more to it than that. When you kill a pathogen cell, it’s likely to rupture and release its toxic contents. So, depending on the extent of your health condition, and the rate at which you kill the pathogen cells, you are going to have countless dead cells in your body, all of them carrying – or leaking – poison.

For more information, you can check via this blog: https://www.spooky2-mall.com/blog/why-do-we-recommend-using-multiple-generators/.

Q: Where to place tens pads in contact mode? Are there any cautions?

Answer: Tens placement is a user decision. The recommended location of the left ankle / right wrist is a general starting point to target the entire body. Makes sense as the electricity has to flow from one end to the other, thus providing coverage across as much of the body as possible.

You can check the instructions via those 2 blogs:

Q: Can you run the same program on two XM generators?

Answer: Yes, you can. However, please make sure they are at least half an hour apart from each other. And please make sure the same frequency is not running at the same time. Otherwise, it will not be good for the people who are receiving the frequencies.

Q: Can Spooky2 be used with a pacemaker?

Answer: No contact mode Rife machine should be used with anyone who has a pacemaker. The electrical energy entering the body can interfere with the pacemaker’s electronics. We recommend Remote Mode as it is much safer.

Q: How to load programs into GeneratorX Pro?

Answer: GeneratorX Pro can be run in standalone mode, which means you can run desired programs without connecting to a computer. We have a blog with instructions:

https://www.spooky2-mall.com/blog/how-to-load-programs-into-generatorx/.

Q: Where to place tens pads in contact mode? Are there any cautions?

You can check the instructions via those 2 blogs:

Q: What source of DNA is for remote rife and how long does it last?

Answer: You can check the answer on this blog:
http://www.spooky2-mall.com/blog/what-source-of-dna-for-remote-rife-and-how-long-it-lasts/.

Q: How to Run Sample Digitizer Scan and Run Preset Using Remote?

Answer: Sample Digitizer scan is one typical kind of Spooky2 biofeedback scan. In this video, we will show you how to run the scan and run preset using Spooky2 Sample Digitizer and Spooky2 Remote: https://www.youtube.com/watch?v=9o6GN3ERLtk&t=1s.

Q: How to load programs into Spooky2 GeneratorX Pro and how delete programs from Spooky2 GeneratorX Pro?

Answer: GeneratorX Pro can be run in standalone mode, which means you can run desired programs without connecting to a computer. We have a blog with instructions: https://www.spooky2-mall.com/blog/how-to-load-programs-into-generatorx/.

You can check the instructions for how to delete programs from Spooky2 GeneratorX Pro via this video: https://www.youtube.com/watch?v=aSoUAM5PBNk.

Q: How to run a biofeedback scan?

Answer: Spooky2 Biofeedback Scan is a powerful tool for listening to your body and discovering what frequencies are best suited for you. To suit people with different needs, there are currently four ways to run biofeedback scans. You can check the details through this blog: https://www.spooky2-mall.com/blog/four-ways-of-running-biofeedback-scans/.

Q: Finish biofeedback scan, should we use healing or killing programs?

Answer: GenX BFB results are for pathogens, parasites, bacteria, etc…. so they should be run in kill mode. The XM will pick up the lower frequencies easier and those can be run in heal or kill. Each of these settings is not far from each other so you can use dual, kill or heal.

Q: What is “reverse lookup”?

Answer: Reverse lookup means to look up a frequency, and report what it does in the database. Here is a file showing what Reverse Lookup finds: https://www.spooky2-mall.com/download/ReverseLookup.pdf. You can check more details on those blogs: 1. https://www.spooky2-mall.com/blog/understanding-reverse-lookup/; 2. https://www.spooky2-mall.com/blog/spooky2-reverse-lookup/.

Q: What’s the difference between Spooky Phanotron Tube and Spooky Straight Tube?

Answer: We have recently released our brand new PhanotronTube that uses the same exacting specifications as the original Royal Rife tubes.

Many users asked about the differences between Spooky Phanotron Tube and Spooky Plasma Tube and which one to choose.

This post will help you understand the differences and choose between the two: https://www.spooky2-mall.com/blog/what-is-the-difference-between-spooky-phanotron-tube-and-spooky-straight-tube/.