Q1: Is it equally effective to run the Terain Protocol on remote as on contact mode?

A: Your choice of mode to get frequencies to the body. Contact requires you to be connected to the generator for the period of the program. While remote allows you to set it up, start it, and go about your business. The Contact on the Spooky2 Central is for cell electroporation, which allows the plasma treatment to go deeper into the cells. To use this contact mode, you just run presets on your central that are designed for Plasma. The frequency coming out of the Contract for Plasma is fixed at 100 Hz.

In order of strength/effectiveness

Plasma – the strongest

Contact

Remote

However for detoxing Terrain Remote would be the best gentler way to approach Terrain Detox.

If you use plasma for terrain, we don’t recommend you to use remote mode for the terrain at the same time too. It may be so strong for you.

Q2: Can you run 2 remotes on the XM?

A: No, you can only run one. But for generator X Pro, it has two independent generators into one. You can run 2 remotes simultaneously.

Q3: Using Gen X, can you run terrain program on G1 port and Herx Helper on G2 port at the same time?

A: Most folks run it several times a year or more and advise to only run Terrain alone. That way, no other frequencies will impact the work Terrain is doing. Once that’s done (after 11 days), you are free to then run multiple programs.

After the first time, you can do what you want. The recommendation to run it alone the first time is to make sure you don’t Herx excessively and overload the detox pathways. Once you’ve run Terrain more than once, you should know how much reaction you have, so know whether it’s okay to run more than it.

Q4: Do you have to be hooked to a pad or coil for standalone?

A: Stand alone allows you to load specific programs to run without using a computer whether is Terrain or Contact or Remote.

Pls check the blog below for how to do it:
https://www.spooky2-mall.com/blog/how-to-load-the-program-and-run-generatorx-pro-standalone/

Q5: Is it recommended to run Terrain more than 11 days?

A: If you run the terrain protocol in Remote mode, it loops itself once 11 days until you manually stop it. If terrain protocol is run in contact or plasma mode, it will run 2-3 hours a day, and you need to manually restart the subsequent presets the next day.

There are four remote presets for detox in the Spooky2 software: Terrain (R) – BY, Terrain-Mercury (R) – BY, Terrain-Nonviolent (R) – BY, and Detox Maintenance (R) – JK.

However, this preset, Terrain-Nonviolent – (R) BY, only runs for 10 days and then repeats itself. But the other Terrain run for 11days and loops.

If you want to know more differences among them, pls feel free to check via:
https://www.spooky2support.com/hc/en-us/articles/217108388-What-is-Terrain-Protocol

Q6: Is “remote” a device that imaprts frequencies?

A: “remote” can be one of the transmission modes that transfer the frequencies to the body. And it can be a device that uses this transmission mode.

Here is the link for it:
https://www.spooky2-mall.com/product/spooky2-remote-v2-0/

Q7: Is it safe to put more than one user’s fingernails in the remote device and treat them at the same time?

A: Yes, you can do it.

The fingernails can be put in one remote together as long as you’re going to run the same programs for them, but we recommend keeping them separate with different paper stickers. Please be kindly noted that it’s not suggested putting human’s and animals’ DNA sample in one remote. And it’s better not to put your DNA sample with people who have serious illness in the same remote.

Q8: Any concern about dirt or nail polish on the nail clipping?

A: It is the DNA in the nail that decides where the energy goes. A nail with nail polish should do fine.

Q9: So I have found that it loops automatically and does NOT shut off. May I know why? How do you use the program without repeating?

A: 1. Keep the repeat sequence to 1. It will not repeat. Keep in mind some presets repeat and you have to do a manual stop.

2. When you have chosen your presets go to programs to choose the program you want. Then on that same programs page at the center bottom is a window which says ‘options’. Third item down is Repeat Sequence. If there is a ‘0’ setting next to it, the program will repeat until you stop it. If you only want it to run once, change the zero to ‘1’. Should you want it to repeat a few more times, put that number in here? Please can explanations be a bit more precise – there are newbie’s out here who feel that they have been given keys to a flying saucer only to be told that the saucer is parked in a shopping mall somewhere out there, use the key and good luck!

3. What preset did you choose? If you select Remote presets, they are set to loop themselves. Remote tends to be 24/7 and can be used nonstop. You can find settings under programs tab. Preset chain or sequence is set to 0. If you want to run it only once, change them to 1.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1351206675041232/

Q10: For killing frequencies and healing frequences, what are the work ranges?

A: It is not the frequency range that differentiates them. For Gex Pro, the frequency Range starts from 0 to 40 MHz for all waveforms.

Killing Mode: Use this mode for pathogen-related issues. It targets bacteria, viruses, and other harmful microorganisms.

Healing Mode: This mode is suitable for conditions not caused by pathogens. It helps restore normal organ function and promotes overall healing.

Pls chek the below blog for more information, hopefully it will help:
https://www.spooky2-mall.com/blog/how-to-distinguish-healing-and-killing-frequency/

Q11: The Generator window says G2 Port 4 4-3 Remove chemical MA. However, myboost and Remote is on G1. This makes no sense. Clearly I made a mistake.What should I do?

A: You can double-check by going into the menu “Utils” and then “Rescan device”. Identifying the correct port you are using is the first step and each time before you start any program, remember always to “Overwrite generator”