Q1: Do Cell Phones interfere with Programs?

A: Do not use your cell phone during biofeedback.

Regarding cell phone use during BFB scan on GenX: When I held my phone or touched it, the scan changed every time I put my hand on or near the phone. I keep it away so I can be sure my scan is accurate. (As a side note: a bug landed on me during a scan, and I screamed & jumped, which made the scan graph jump. I re-started that scan too.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2139942539500971/

Q2: Can I place a large 3 gallon glass container of water between the suitcases?

A: A large water container may take longer to have the frequencies imprinted. Perhaps an hour may be required for this type of volume. After this time, the water will contain the frequency information of the scalar field.

Q3: How do you prove a scalar field exists and know that it is scalar as opposed to EM field or other?

A: The Scalar field passes through the Faraday cage while the EMF field does not.
You can put those two boxes in different rooms, and the receiver light will still be on.

Q4: How long should we run MW frequencies? What’s the dosage?

A: These are experimental because our body will take what it needs and will pass on through what it doesn’t need. However, it’s a good idea to know what an overdose of any substance looks/feels like. That is indicative when you’ve reached your max.

I once heard that plasma 1-3x is close to one dose. Plasma is supposedly 20-40x stronger than remote. 10-20x stronger than contact. Does that mean running a frequency 20x on remote would equal one dose? No one can say. Seems like it would be too much.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1912352735593287/ 

Q5: How do I change the dwell time?

A: There are two ways.

1. Create a whole new frequency program and specify the dwell you want to use on a per frequency or overall basis.
2. Use the dwell multiplier feature on the programs page to multiply the dwells by a common factor.

#2 is the easiest method.

For instance, let’s say the programs in question have a default dwell of 180 seconds (3 minutes) and I want to have it fun for 5 minutes. I can use a dwell multiplier of 2 and settle for 6 minutes or use a dwell multiplier of 1.6665 to run for 5 minutes (4.9995 to be exact).

Keep in mind that anything that has an override like say one frequency may run for 5 minutes already, will be adjusted at the same ratio.

For more details, please check:
https://www.facebook.com/groups/spooky2/permalink/1070109026484333/

Q6: How long does an imprinted holographic sticker last? Any suggestions on how to keep the holographic stickers to stay on better?

A: Imprinted holographic stickers can last for a very long time. They can last as long as they do not get wet, worn out, or exposed to the sun and strong magnetic fields.

Many like myself put them in a plastic coin holder and keep them in a pocket. They last longer. I use a plastic coin holder or a very, very small ziplock baggie.

More details here: https://www.facebook.com/groups/spooky2/posts/2583561988472355/

Q7: What is the best material for frequency imprinting?

A: Quartz crystal is possibly the best thing, but clean high-quality sand, water, oils, other gemstones, silver, copper, and gold are also good. Lots of people like hologram stickers too. It depends on what you are doing and how you want/need to use it.

Q8: Is it better to imprint from the Central or the generator?

A: Generally speaking, it is better to imprint from the generator. Plasma is a broad-spectrum transmission device. You can put a nice clean frequency into a plasma tube, and what you get out is a Smorgasbord of harmonics from the tube. When you imprint frequencies into the water, generally, the idea is to put known frequencies into the water. If you are using your plasma, you are putting a whole lot of frequencies into the water. So it may or may not be what you want to do. So most people will use a coil or the Spooky2 Cold Laser to imprint frequencies.
However, Spooky2 Central is the most powerful tool you can use for very serious conditions, such as very serious cancers. If you are currently treating yourself with Spooky2 Central, it may be a wonderful idea to have a vial of water nearby, and treat that whilst treating yourself with the plasma tube, and then between sessions, you can drink that water.
Spooky2 is wonderful for experimentation, and we get a lot of feedback from people for ideas, so this may be an idea where you can treat yourself with plasma during one session and then you can also treat yourself between sessions with water that has been imprinted with exactly the same frequencies that you have applied.

Q9: Will the EMF be imprinted into the water?

A: The water does have the low frequency from the EMF but not much, as low frequencies take longer to imprint. The EMF is not absorbed and retained. Only the frequency of 50 or 60 Hz.

Q10: Will it be overdosage if the imprinting time is too low?

A: There shouldn’t be any concern about overdoing the imprinting since JW has said that with scalar fields, your body and the water/substance will take what it needs and discard any excess. So the only real concern should be if the imprinting is long enough or too short.

Q11: Can you explain why it’s recommended to put water to imprint on the transmitter, while substances to transmit molecular information should be placed on the receiver?

A: The energy flows from the transmitter to the receiver, then back. There is no scalar field until it hits the receiver and then returns back to the transmitter.

Therefore, in order to add substance information to the field, the first entry point is the receiver coil. That information is then carried back to the transmitter. Once at the transmitter, the information can be imprinted to whatever is on the transmitter coil.

I did one experiment to test the properties of the transmitter coil vs. receiver coil in regards to structuring water. I’ll post a thread on this.

Thread created and can be found here:
https://www.spooky2.com/forums/viewtopic.php?f=117&t=9823

Q12: For imprinting, where do I put the i.e. glass of water and the essential oils?

A: The vial of water goes on the transmitter. A full glass is too much water. And the Essential oil on the receiver coil.

Q13: Is there anything I need to do before imprinting water to make it more effective?

A: You could try vortexing water. I believe it should precede imprinting.

So it’s more about making water structured than imprinting, but one shouldn’t plant roses when forests are on fire :). When you have water structured, then imprinting it is far easier and long lasting, I believe.

There’s a simple way of making water structured via applying a Spooky2-XM generator, and a one-dollar electric motor (and a vortex).
I made a film showing the procedure – it’s in Polish, but self-explaining, all the more I added an explanation in English under the film. You may want to see it: https://youtu.be/r9AYSkoo9QA

The water I get after 15 min of vortexing is something much more than I expected. Water is absolutely tasty. If you want to know what “absolutely tasty water” means follow this procedure and drink the water.
Additionally, only with such water further steps (imprinting) “get wings”, I believe.

For more details, please check the link from:
https://www.spooky2.com/forums/viewtopic.php?f=6&t=10409