Q1: Can we directly convert a user remote preset to a contact preset?

A: Yes. It takes 3 steps.

1. Click on your remote program.
2. Untick “Load Programs/Notes” (underneath the button on the top left of Presets tab)
3. Click on the shell preset for your desired hardware (i.e., “Spooky Cold Laser (L) – JW”).

At this point, either load into the generator or save the preset.

For more details, please check the link: https://www.facebook.com/groups/spooky2/permalink/1341094802719086/

Q2: Is direct contact much more effective than remote?

A: Depends on the measurement basis… If you are talking about effectiveness per day – Remote and Contact are approximately the same. 

Yet, if you talk about hours connected to gear, Remote wins hands down, because you don’t need to ever be connected…

If you are talking about per day, they are roughly equivalent in effectiveness per calendar day. If you talk about one hour of computer time for each, then Contact wins – because remote runs 24 hours per day… It is all about perspective. For me, Remote wins big because I don’t ever need to be tied to the computer for normal programs.

Just need connection for biofeedback sessions – which are equivalent between all modalities.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2096626683832557/

Q3: So if you have mechanical knees you cannot use contact mode?

A: We do not recommend you use contact mode if you have electronic implants like pacemakers. But contact mode is safe to use with metal replacements.

Q4: What if contact mode makes you feel a little sick when using biofeedback?

A: There are a number of reasons one would experience shocks and a number of ways to avoid it. Please review to see if this applies to your situation.

For more details, you can check the blog: https://www.spooky2-mall.com/blog/what-you-can-do-when-you-experience-shocks-in-contact-mode/

Q5: Can the tens pads be re-used? Can I use my pads on other people?

A: Yes. You can use them until they no longer stick to the body.

You can also use your pads on other people. If your friend wants to try contact mode, you can borrow your pads for her to use. But you can’t put one pad on you and the other on someone else while doing the treatment.

TENS Units are highly reusable making them very cost-effective. In fact, the only thing you need to replace is the electrode pads. However, they cost money and after several uses, these pads will lose their stickiness because of the body oils and other transient debris that stick to their surface during regular use. So, if you want your TENS electrodes to remain stickier longer, simply cleaning the pad surface after every use will extend their life saving you money. Cleaning TENS Pads is easy. To clean TENS electrode pads wipe them gently with a damp cloth. This will remove some of the dirt, oils, and other by-products that end up adhering to the tacky pads.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1796157107212851/ 

Q6: What is the most effective mode for ACNE?

A: You can run all the acne frequencies in the database. Select Remove duplicate frequencies, dwell .35 and your total run time is 45 min ( with dwell= 1 a little over 2 hours). Along with that you might apply Vicks Vaporub on the acne.

For more details, please check:
https://www.facebook.com/groups/spooky2/permalink/551817958313445/

Q7: Should I run scan results with killing or healing preset?

A: Your scan will be based on Hulda Clark’s frequencies for pathogens. The result of the scan will be based on these frequencies, therefore, you would want to kill them.
Please don’t forget to run the detox simultaneously, if, you have more than one generator. If you only have one, then please do it immediately after the treatment.

Please check this blog:
What do we do after we get results from biofeedback scan using Spooky2 Pulse
http://www.spooky2-mall.com/blog/what-do-we-do-after-we-get-results-from-biofeedback-scan-using-spooky-pulse

Q8: Is hand cylinders as effective as tens pads?

A: Spooky2 Tens pads are easier to use because they can stick to your body, hand cylinders you would have to hold in your hands for the whole treatment time. Effectiveness wise I believe they are the same. So, most people use tens pads for contact mode. For foot baths you can use the metal hand cylinders and can’t use tens pads for that. Also, for biofeedback you need to use (or way better off using) tens pads due to where you have to place them. Lastly hand cylinders are limited to your hands and foot baths. Tens pads you can pretty much put anywhere below your shoulders and focus on specific areas.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2292007304294493/

Q9: Where is the best place to place the tens pads for breast cancer in the liver?

A:You can place the TENS pads across the breast without the signal going through the heart.

Q10: If I do BFB scan by using tens pad, do I need to use high power port?

A: Yes, you need. Spooky2 Biofeedback Scan is a powerful tool for listening to your body and discovering what frequencies are best suited for you. To suit people with different needs, there are currently four ways to run biofeedback scans. For more details about BFB scan, you can check the link:  https://www.spooky2-mall.com/blog/four-ways-of-running-biofeedback-scans/

Q11: Can you use pads and coil at the same time on 2 output, same booster?

A: No, you can’t.

1. I think your suggested method is incorrect as the power will end up being diminished for both the TENS Pads and the PEMF Coil so you are better off running two Generators one for each delivery method.
2. Contact (TENS) require a minimum amplitude in order to penetrate the skin layer. If you split the amplitude with having another device connected then you likely will not receive enough benefit to receive contact treatment.

For more details, please check the link: https://www.facebook.com/groups/spooky2/permalink/1183483381813563/

Q12: I found the hand cylinders to be shocking me….I wound up sitting on one and placing one behind my back…. other ideas?

A: You can have one on a hand and the other on your foot. It would be impossible to bypass the current then put one hand cylinder under your foot. Use a damp cloth to make good contact.

For how to use Spooky2 hand cylinders to do foot bath:
https://www.spooky2-mall.com/blog/how-to-do-foot-bath-using-spooky2-hand-cylinders/

Q13: Would you explain the difference between selecting Angle + Current and performing the Current and Angle?

A: I can give you a quick (well detailed so hopefully quick) description via an example.

When you take and pull out frequencies using current, we are looking for the ones that had the most change from the prior measured frequency.

When you take and pull out frequencies using angle, we are looking for the same, but using phase angle.

When you take and pull out frequencies using angle+current, we literally add the two measurements together and pull the frequencies from the combined metrics.

For more details, you can check the link: https://www.spooky2support.com/hc/en-us/articles/360002149534-Would-you-explain-the-difference-between-selecting-Angle-Current-and-performing-the-Current-and-Angle-