Q1: I have a relative that just had knee surgery. Where should he place the stickers to promote healing? Would it help more if he used more than one sticker at a time?

A: You can attach the sticker over the surgical area (if the skin is intact and not irritated) or on clothing/sleeves covering the knee. If direct contact isn’t possible (e.g., due to bandages), place it on the thigh or calf close to the knee.

Using multiple stickers with various healing frequencies (e.g., tissue repair, pain relief) may enhance results, but prioritize proper spacing（avoid overcrowding: Space stickers a few inches apart to avoid potential interference）and imprinting quality. Combine this with rest, hydration, and conventional care for optimal recovery.

Q2: When is it better to use imprinting vs. the remote function of Spooky?

A: First, pls consider the modality, for example, if in pathogens killing, then imprinting is not that ideal. But you could use imprinting for relief, and healing conditions. Imprinting is not a replacement for Spooky2 remote therapy, it is a supportive way instead. So we can not say which one is better.

Q3: When I put the essential oil on the circle plate of the Scalar receiver, the light on the receiver becomes dim, does this mean it reduce the strength of the transmission between the transmitter and receiver? The more stuff I put on the circle plate, the dimmer the light is?

A: The dimming receiver light is normal when using Molecular Scalar mode(essential oils, drugs, etc.). It indicates that the scalar field is interacting with the molecules, not necessarily weakening.

Q4: Have you imprinted other items such as crystals? How long does the frequency last in the imprinted object?

A: Yes, and it can last for several months. Also imprinted holographic stickers can last for a very long time. They can last as long as they do not get wet, worn out, or exposed to the sun and strong magnetic fields.

Q5: What is the sine in the settings and why do you change it?

A: In Spooky2 software,”Sine” refers to the waveform used for frequency generation. It is the purest and most natural waveform, representing a smooth, periodic oscillation without distortion. When imprinting frequencies, the sine wave is recommended for its Purity & Accuracy, Consistency, Better Resonance with Water.

When to Use Other Waveforms? For example, Square Wave: Used in some presets for stronger “attack” (e.g., pathogen-killing frequencies). Sawtooth/Pulse Waves: Sometimes used for specific biofeedback or detox protocols.

Pls also check the below link for many other waveforms for more ideas:
https://www.spooky2-mall.com/blog/which-waveform-to-use-in-rife/

Q6: Which programs can I use against handy radiation?

A: Pls check how our users comment on this:
https://www.spooky2support.com/hc/en-us/articles/1260804159849-How-can-Spooky2-assist-to-relieve-the-damage-that-is-caused-by-radiation

Q7: What is the difference in changing the multiplier to .00555. I have been changing it to .5?

A: .5 means 90sec for each frequency​​

Best for low frequencies (e.g., Schumann Resonance 7.83Hz), which need more time to imprint.

Example: If running a 30-minute program, fewer frequencies will be applied.

Lower Multipliers (e.g., 0.00555 = 1 sec/freq)​​

Ideal for high frequencies (e.g., molecular weight or pathogen-killing frequencies)​​.

Allows imprinting hundreds of frequencies quickly without excessive runtime.

Q8: How many times can you use a holographic sticker? Is it save to have beside lap tops iPhones and watches?

A: There is no limit to use the stickers. You can always re-imprint after a time to enhance its effectiveness. Simply place it on your body to enjoy its subtle yet powerful effects.

Q9: How to imprint frequencies on a copper bracelet?

A: It depends on which transmission modes you are using?

For example,

By Remote mode:

Clean the bracelet to remove any energetic residues (e.g., swipe a magnet over it or leave it under sunlight for a few minutes). Attach holographic sticker to the copper surface. Connect your Spooky2 generator (XM or GenX Pro) to the software. Select Remote Mode in the software. Choose a preset: For general use: Select “Universal Square H-Bomb” preset.

By PEMF mode:

Clean the bracelet as above instructions. Place the copper bracelet on top of the PEMF coil’s hole (or inside if small enough). Run frequencies via the generator.

Q10: Is using a Scalar the same process?

A: To perform this, you will need a source of water like bottled water. Turn on Spooky2 Scalar. Place the cup on the output coil located on the transmitter box. Then tune your Spooky2 Scalar accordingly. Leave the cup on the coil while you are doing Scalar treatment, such as pure scalar, molecular scalar and rife scalar.