Q1：I was never told to run an empty slide first when doing a bfb scan?

A: It is not mandatory, but you can run a baseline scan with empty slides first, especially when there is much electrical noise. When you run a Baseline scan, the system records background noise without any sample. This allows Spooky2 to ignore disturbances like Wi-Fi signals and electrical interference, improving scan accuracy. Once the Baseline is complete, you can proceed with your biofeedback scan as usual.For more details, please click here:
https://www.spooky2-mall.com/blog/maximizing-biofeedback-accuracy-with-spooky2s-baseline/
https://www.spooky2-mall.com/blog/improving-the-accuracy-of-your-biofeedback-results/

Q2: Can you place multiple types of DNA in one sample such as urine, saliva and blood?

A: It can be possible, since Spooky2 will scan the combined sample. But it’s not the best practice. The digitizer reads whatever resonance is between the plates, so mixing blurs which source a frequency belongs to. For clearer results, scan each sample separately on its own cleaned slide, then review the hits side by side. And remember — one slide set per person, never shared, alcohol-cleaned between uses.

Q3: Does the urine sample on the scalar need to be mid stream?

A: There is no specific requirement that the urine sample used on the Spooky2 Scalar must be a midstream sample. You can use urine as a biological sample for scanning with the Scalar Digitizer without needing to focus on midstream collection. But midstream fresh urine is the recommended collect method (discard first/last flow) by many of our users in their practice so you’re modulating the field with your own clean biochemical fingerprint. But it’s not rigid and first-morning urine is also widely used on the coil and is richer in hormones/metabolites. Either way: fresh, clean glass, no toilet contact.

Q4: I live alone in a two story house. I have my scalar set up in upper floor to opposite area on first floor. My scalar field is large. Will I get the affects, or do I have to place the scalar receiver closer to the transmitter?

A: we need to understand that the scalar field balloons out between the transmitter and receiver. If the two are far apart, the signal becomes wider.With one Scalar box upstairs and one downstairs tuned to the first peak, the scalar field spans both floors where you don’t need to sit next to the receiver. Any part of your body inside that field receives it.

Q5: Can I reuse the sample plates for digitizer? How to properly clean them for reuse? How many times can I reuse the sample plates?

A: You can reuse the Spooky2 Sample Digitizer slides, but they are designed as disposable replacement slides. For reuse:

Clean the slides gently with rubbing alcohol (alcohol wipes work well).

Do not use water or hydrogen peroxide to clean the plates, as water damages them.

Allow the slides to dry thoroughly between uses.

It is best to use two slides in rotation, giving each slide a day to dry completely.

With proper cleaning, many of our users report that each slide can typically be reused 5 to 10 times.

Important: Do not use the same slides for different people to avoid cross-contamination.

If you want to maintain optimal performance, consider replacing the slides regularly. Replacement packs of 5 pairs are available for purchase.

For more details, you can visit:
https://www.spooky2-mall.com/product/spooky2-sample-digitizer-replacement-slides/

Q6: Can the urine show heavy metals in the scan?

A: Urine does contain excreted heavy-metal residues in real lab testing, but the Sample Digitizer scan isn’t built to directly report ‘heavy metals present.’ It’s a pathogen/resonance biofeedback tool. Metals may show up indirectly through detox-program hits, biofilm patterns, or kidney/liver stress frequencies, but you can’t quantify mercury/cadmium from it. For actual metal burden, it is suggested to use a clinical timed-urine or blood test.

For heavy metal detoxification, Spooky2 recommends using the Remote mode with specific programs like “Detox Heavy Metals 2” which target heavy metals in the body more effectively.

If you want to focus on heavy metal detection and detox, using Remote mode with a DNA sample or other biological samples in combination with the appropriate detox programs is the best approach.

For more information on heavy metal detox with Spooky2, you can visit:
https://www.spooky2-mall.com/blog/can-spooky2-help-with-heavy-metal-detox/

Q7: Would you run the Terrain protocol using a separate generator or on the same generator running the Sample Digitizer results?

A: The best practice: run the Sample Digitizer results and the Terrain protocol on two separate generators if you have them — one does targeted pathogen work, the other prepares the terrain. If you only have one generator, run the Digitizer hits first, then switch to Terrain afterward.

Q8: During a molecular scalar urine scan, do the physical body need to be in the Scalar field with urine at the receiver?

A: This is not a scan, but a treatment. During a molecular scalar urine treatment with the Spooky2 Scalar, the physical body should be present in the scalar field while the urine sample is placed on the receiver coil. You sit or lie between the transmitter and receiver to receive the scalar energy, which is modulated by the information from the urine sample on the receiver coil. This setup allows the scalar field to carry the healing or diagnostic information from the sample to your body effectively.

Q9: Can I run Remote “Kidney Balance” 24/7, while I run Scalar-Rife treatment at night? Or do I have to stop the remote?

A: Yes, you can run the Remote Kidney Balance program 24/7 while simultaneously running Scalar-Rife treatment at night. Many users combine different Spooky2 modalities like Remote and Scalar at the same time without needing to stop one for the other.

Just be sure to monitor how your body responds to the combined treatments. If you feel any discomfort, you should pause or adjust the sessions accordingly. Staying well-hydrated during treatments is also important.

Q10: How many presets can we combine in 1 session in Scalar? Less than 4 hours?

A: You can create a custom preset by combining several programs, but it’s best to keep the total run time under 4 hours and then let it loop if needed. This approach helps manage treatment intensity and allows your body to respond well.

If you want to combine multiple presets in Scalar mode, consider:

Keeping the total session length under 4 hours.

Monitoring your body’s response and adjusting accordingly.

Running fewer presets per session and rotating others in subsequent sessions.

For more detailed guidance on creating and managing presets, you can visit:
https://www.spooky2-mall.com/blog/how-to-make-your-own-presets-out-of-shell-presets-october-software-version/