Q1: If a person has titanium plates and screws in legs/spine, should contact mode be contraindicated?

A: We do not recommend you use contact mode if you have electronic implants like pacemakers. But contact mode is safe to use with metal replacements.

Q2: What’s the difference between Spooky2 Tens Pads and Hand Cylinders?

A: Spooky2 Tens pads are easier to use because they can stick to your body, hand cylinders you would have to hold in your hands for the whole treatment time. Effectiveness wise I believe they are the same. So, most people use tens pads for contact mode. For foot baths you can use the metal hand cylinders and can’t use tens pads for that. Also, for biofeedback you need to use (or way better off using) tens pads due to where you have to place them. Lastly hand cylinders are limited to your hands and foot baths. Tens pads you can pretty much put anywhere below your shoulders and focus on specific areas.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2292007304294493/

Q3: Placement of pads for prostate treatment?

A: Please check the Tens pads placement from the link:
http://www.spooky2-mall.com/blog/where-to-place-tens-pads/

Q4: Where is the best place to place tens pads for treating breast cancer?

A:You can place the TENS pads across the breast without the signal going through the heart.

Q5: Where should I place my pads on my body for sore throat, bronchitis, and cough, upper respiratory infection with no fever? Should I use the boost? Which port do I plug the pads into?

A:Let’s see what our users said about it:

1. I started colloidal silver spray in nostrils, CS drops in ears followed by swimmers ear drop a little later to dry it out. I also did BFB using GX contact pads. The CS helped a lot.

2. I would be using the BN port on the boost as well as putting the contacts on each side of my chest personally.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1539012602927304/

Q6: Can you explain difference between spooky central and plasma?

A: Spooky2 Central is currently the most powerful Rife machine that can apply Royal Rife’s original frequencies directly without a carrier. It has gained favor among many users due to its exceptional effectiveness in targeting severe conditions. Spooky2 Central contains four modes: Plasma, Ultrasonic, PEMF, and Contact. Each mode of Spooky2 Central can be used individually or combined for enhanced effectiveness.

For the specific features of the four modes, you can read this blog: 
https://www.spooky2-mall.com/blog/what-are-the-advantages-of-spooky2-central/

You can learn Spooky2 Central success story here:
https://www.spooky2reviews.com/category/product/spooky-central/

Source: 
https://www.facebook.com/groups/spooky2/posts/2735064279988791/

Q7: If you place the TENS pads (in error probably), on your lungs. is that too close to the heart?

A: As long as not over the heart. You can choose the right lung and do front and back placement. Or you can do the lower portion of each lung so you are away from the heart.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2170617589766799/

Q8: Is treatment on higher power port more effective than on say the colloidal silver port?

A: The difference:

When you use the CS port vs. the High Power Contact port, the difference physically, as commented above, is that there is a 10k Ohm resistor inline with the CS port.

What this does is limits current flow.

When you use frequencies that are over 10kHz on either port, you won’t usually feel anything as there is no resonance with your nervous system.

The reason you feel the lower frequencies is that it resonates with your nerves and causes the muscles to fire.

Typically use the CS port if you are running low frequencies and felt too much even with the contact settings in effect to reduce the likely hood of feeling too much (Reduce Amp, Amp Ramp, etc.).

Now for the other main difference between the two.

The High Power Contact port allows higher harmonic frequencies to be passed into the body. The 10k Ohm resistor that limits current in the CS port also filters these very high harmonics out.

The CS port was initially created to limit current to provide a better Colloidal Silver creation process. The side effect is that it also provides a very safe contact session as you can not get too much current in this mode.

However, some devices like PEMF would not benefit from limited current, so the High Power contact port was then added in the Boost 3.0

That pretty much covers the difference between the two.

Q9: Why do the tens pads turn white and get a burn in the area when using the them?

A: 1. You could set polarity change every 60 seconds in the Settings tab, or set lower voltage, in order to avoid burns.

2. This could be acid build-up. If this is the case, make sure you’ve run the Terrain protocol, as this will help reduce this kind of buildup.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1708364645992098/

Q10: Can you please let me know where to put the tens pads for a biofeedback scan?

A: One on the back of the right hand, the other just below the outside ankle of your left foot.

Q11: Can you explain Herx? Is that over detoxing too fast? Or what is that exactly?

A: A Rife machine will have no side effects, but may create a healing crisis, otherwise known as a Herxheimer reaction, a detoxification response. Excessively large amounts of microbial or cancer cell waste and toxins hinder the body’s ability to adequately eliminate it through the usual channels (breakdown by the liver, through the colon or urinary tract).

So instead, the toxic material is discharged through the lungs, sinuses and skin. Symptoms can include a flu-like condition, heavy perspiration and night sweats, fever, with or without chills, headaches, malaise, diarrhea, nausea and vomiting, pain in joints and bones, and itching, flushing, and reddening of skin.

The above can apply to even a detox protocol where toxins are not being produced by die off, but are being released back into the bloodstream from where they were hiding (joints, muscle tissue, etc.).

If this happens your likely target is eliciting a response. Could be an indication that there is a lot of work to be done by these frequencies and may have done too much too fast.

Try a lower amplitude setting next time you run these sets. Suggest you take a break until your body is able to flush out what toxins it is processing.

Q12: When running a program, how do you get it to run only once, instead of ‘eternally’ ?

A: On the programs page if you hoverboards your mouse over the number arrow is pointing to you will see options. See pic and Happy Rifing!