Q1: While in the Scalar field , are we allowed to use a cell phone , a laptop or watch TV?

A: Yes, we can use them. For best results, it’s recommended to minimize the use of devices emitting strong RF signals near the scalar field, but using them is not prohibited and will not cause damage. If you want to avoid any interference, try to keep devices at a reasonable distance from the scalar transmitter.

Q2: How can you specify that you want to scan the head/thyroid?

A: After you set the device and choose the preset such as Spooky Scalar General (SS) – JW. Then it is time to navigate to the Programs tab and search for programs related to the head or thyroid, for example, you can search for“Thyroid” or “Head” or specific conditions like“Hypothyroidism” or“Nodules”. This method allows you to tailor the scalar energy treatment specifically to the head or thyroid by using targeted frequency programs designed for those areas.

Q3: How often do you change your dog’s nails in the remote when using your rife machine?

A: Dog’s nails last for a very long time since the DNA in nails is protected by hard keratin. However, to maintain optimal effectiveness, you may choose to renew the nail samples periodically. Some of our trainers and users will change it monthly or a longer period. When using nails in the Remote, make sure the sample is properly prepared by placing the nail clippings between stickers and then into the Remote.

Q4: Is it ok to have programs running on a Spooky 2 remote at the same time as being in the scalar field, either pure or other?

A: Yes, it is generally okay to have programs running on your Spooky2 Remote while you are in the Spooky2 Scalar field (whether pure scalar or other scalar modes). These two modalities work differently and can complement each other: Spooky2 Remote uses quantum entanglement with DNA samples to deliver frequency treatments remotely.Spooky2 Scalar generates a scalar energy field that you can physically be in, which works directly on your body with higher power scalar waves.Since the Remote transmits information remotely and Scalar provides a local scalar energy field, running both simultaneously should not interfere with each other and may enhance your overall experience. However, if you notice any discomfort or unusual sensations, you can adjust the usage accordingly. Always ensure your equipment is set up properly and running smoothly.

Q5: What does the moving chart mean on the control tab and why does it light up green and red?

A: The moving chart on the Control tab in the Spooky2 software represents the current and angle of the GeneratorX connected to your scalar system when you are in the Scalar field. It shows real-time data about the scalar field’s activity. When you place your hand or an object in the scalar field, the graph will show a bump or movement, indicating that the scalar field is responding to changes in the environment.If the graph remains flat, it means there is little or no interaction detected in the scalar field. The green and red lights on the chart indicate different states of the scalar field or biofeedback scan: Green light usually means the system is operating normally and detecting signals. Red light may indicate a specific response or alert during the scan or tuning process.

Q6: If you use GenX Pro with contact and use scalar: using the same frequency. Is it increasing the effect?

A: Combining both can create a complementary effect—targeted local treatment plus whole-body scalar energy exposure—which may increase the overall benefit.However, the exact increase in effect can vary depending on individual response and the condition being treated. Many users report enhanced results when using both together. Always listen to your own body when combining treatments.

Q7: When imprinting crystals can we place them directly onto the transmitter? or do we need a radionics?

A: Yes, you can. You can imprint crystals by placing them directly onto the Spooky2 Remote or other imprinting devices without necessarily needing a radionics machine. If you are using other Spooky2 imprinting methods like the Scalar or PEMF Coil, you can place the crystal on the transmitter coil or in the central hole of the coil, depending on the device. Radionics is an option but not a requirement for crystal imprinting.

Q8: When doing baseline scan, do you need to sit or lie in the scalar field?

A: No need, after you set the scan, then leave it there to finish its job without your presence. And once it is ready, then you come back into the field.

Q9: When the scans are saved onto the database…is that database only visible on our computer or does it load up to the Spooky2 overarching database?

A: When you save your scan results in Spooky2 software, the data is stored locally on your computer in your Spooky2 database. It does not automatically upload or sync to the Spooky2 overarching or central database.

This means:

Your saved scan results are private and only accessible on your own computer.

You can search, run, and manage these saved programs within your local Spooky2 software.

The Spooky2 database on your computer will refresh automatically after adding new programs, but this is still local to your system.

If you want to share or compare results with others, you would need to export or manually share the data yourself.

Q10: The long cable with the scalar is not long enough to go anywhere but across us when we sleep. Is that okay?

A: You can try Scalar Link Cable Extension. This coupler connects two link cables securely together, allowing the two scalar boxes to be placed further apart. This produces a longer and wider scalar field. Check it out via the link below:
https://www.spooky2scalar.com/product/scalar-link-cable-extension/

Q11: Is there a book for Spooky2 that goes in-depth step by step?

A: Yes, we do have a Spooky2 quick guide:
https://www.spooky2-mall.com/download/spooky2_quick_guide_20241218.pdf or you can find it on the software under Help buttom.