Q1: I use the PEMF coil for imprinting and have not been using the boost, but rather connecting to out 1 of the XM, is this still effective?

A: Yes, it is totally fine. Please check the video to know more about how to do imprinting with the PEMF coil: https://www.youtube.com/watch?v=v_aToNFIprs

Q2: Can two devices be used on the same generator (out 1 and out 2) at the same time?

A: Using the \Shell (Empty) Presets\Spooky Cold Laser – JW Preset, you can wire your Cold Laser to Out 1, and the PEMF Coil to Out 2 and deliver frequencies using both methods at the same time.

WARNING: Do not use a boosted port. If the boost is wired to the generator, use the Out 1 and Out 2 pass-through ports. Use of a boosted port with the laser can result in damage to the laser.

Q3: Is it possible to add other programs to a preset using the chain option?

A: Using Chain Editor you can insert new programs.

Download Chain editor and install into C:\Spooky2 folder.
https://www.cancerclinic.co.nz/

For more details, please check the link from:
https://www.spooky2.com/forums/viewtopic.php?f=5&t=10594

Q4: I have the blue machine. Can I run 2 programs at once?

A: You can make a custom remote preset containing various relevant programs, but it’s best to keep it under 4 hours in length, and then let it loop. In other words, it automatically returns to the beginning after four hours and repeats the same frequencies. The recommended runs = 120 passes, i.e. you allow the preset to run 120 times 24/7.

Q5: How long should we keep the PEMF coil on a skin?

A: Spooky2 has no limits. You can use it as long as you like. There are no adverse effects from using the coil too long. Treatments can safely be performed overnight.

Sometimes use of the PEMF coil with frequency sets can result in a Herx reaction. This happens when pathogens are killed and the poisons they contain are released. So take care and slowly build up treatment durations.

Q6: What is the advantage of using the PEMF coil over other modes of transmission?

A: 1.It’s good for targeting localized issues…I used a PEMF mat to speed my hubby’s overall healing (and lessening of pain) after his heel surgery several years ago. It’s also used a lot for sports injuries I think, for that reason.

2.The PEMF frequency and the settings are fixed within Spooky2 Central.Spooky2 PEMF Coil connected to a generator allows you to change waveforms and other settings that you can experiment with.

The PEMF coil has upper frequency limitations and produces more power (magnetic flux – guass) at lower frequencies.

My comparison of treatment options: 
https://spooky2.com/forums/viewtopic.php?t=11637

For more details, please click this link:
https://www.spooky2.com/forums/viewtopic.phpf=23&t=15233&sid=1a5986e3eb08f2b9e0147f25098ba559

Q7: Do I need to move PEMF coil around or keep it in the same spot?

A: Your choice. If the spot you are working on is focused, you don’t need to move it.

If the area you are working on is much larger, then moving it over time would be appropriate. However, you don’t need to move it as if you are massaging the area.

Depending on how many frequencies you are using (I just use 1 typically), you may wish to move it every 15m or after one loop of your frequency list has been applied.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2044850782343481/

Q8: What frequencies should I use with Spooky2 PEMF Coil?

A: The lower frequencies are the best, say under 30 Hz, even better are those around 10 Hz.

For more details, please check:
https://www.facebook.com/groups/spooky2/permalink/1065320053629897/

Q9: What are the upper frequency limits for using the cold laser?

A: I’m not sure the specifications includes that information, but any frequency lower than 1MHz should be fine. Somewhere between 1and 10 MHz performance will degrade until the Lasers don’t light at all, but even when they are lit, they will be less bright due to the amount of time to turn on is long enough that they don’t reach full brightness.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2140190886142803/

Q10: Can the cold laser help with neuropathy?

A: Yes. The nerves are within a half inch (or 1 cm) from the surface of the skin.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1462886023873296/

Q11: How do you treat neck pain and arthritis if you can’t use contact above the shoulders?

A: The PEMF coil is good for pain, and it can be applied on the neck and head. Use low frequencies (like under 50 Hz), they work better for the coil.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/3348934205268459/

Q12: What’s the difference between connect PEMF coil to Out1 directly and connecting PEMF Coil via a booster?

A: Out 1 by itself is limited to 20v peak to peak.

Boosted port using 20v and inverse+sync provides up to 40v peak to peak.

When you double the voltage, you square the power.

Other than this, there is no difference in output frequency wise.

Given that the PEFM coil was original driven by the SC at a fixed frequency of 100 Hz and at +29VDC which equates to 58v peak to peak, you will want to try and keep it boosted.

If you don’t have a boost, while at 20v peak to peak, it may still offer some therapeutic effects.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/654866288008611/

Q13: Can you use the cold laser on your neck?

A: Yes. It won’t penetrate very deeply, though.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2197387840423107/