Q&A of Amal Douglas Spooky2 FAQs Training Course

Q1: I’m curious about what to do when I occasionally hear “generator error”?

A: This is typically either a loose connection (meaning cable not secure, or faulty cable), or micro-brownouts can cause this too. For the micro-brownout issue, you can buy a UPS (Uninterruptible Power Supply) from Amazon and this will protect you against these brownouts.

But when this happens, shut down the computer, turn off the generators, then turn everything back on again.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1788538397974722/

Q2: Do you need more than 1 generator for a family of 3? or can the generator be shared?

A: 1. It depends on your budget and health concerns. You can do detox for everyone with 1 generator, if there are any common issues can be treated the same way.

2. With remote you can put multiple DNA samples in one remote and treat all those people (via their DNA) at the same time.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1548851068610124/

Q3: Is Spooky able to scan for good bacteria or missing goof bacteria？

A: 1. There is no “filter” mechanism. Generator X pro is finding the resonant points of all tissue between the TENS pads, so it is important to place them close to the problem area.

2. BFB scan can’t really tell the bacteria is good or bad, but it is more likely to find bad bacteria, as this makes up more biomass. When you run scan results, please take probiotics which contain more types of good bacteria.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1254372994724601/

Q4: Would it be to much to do terrain in contact and remote at the same time?

A: Yes, you just need to choose one mode to run the terrain. No need to run it both on Remote and Contact.

Q5: With the Gen X pro, when don’t you use the boost?

A: Generally speaking:

use the boost when running contact & remote programs;
do not use the boost when biofeedback scanning.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1884655551696339/

Q6: Which wrist do you use? I’ve seen people saying left, not the left . . . Right wrist and left ankle? Which is it or doesn’t it matter?

A: Move the pads to different points on your wrist and ankle. Do not do left wrist to the right ankle. This will cause the current to go directly through the heart. And you don’t want this.

For more information, please check this link:
https://www.facebook.com/groups/spooky2/permalink/1772009462960949/

Q7: When running terrain program , can u talk about how to support the “detox “ part of the body and is there a program one should run at the same time to support the detox? Best to use same time if have pro or do after the terrain done? Sorry totally new..

A: At Spooky2, we always recommend our users to run the Terrain Protocol Preset for detoxification before starting their Rife frequency treatment. Detoxification is important before you run any Rife treatment programs.

Many people may not notice the fact that they have toxins build up in their body system. These excess toxins will actually cause physical and mental health problems such as chronic fatigue, headaches, insomnia and diseases. Many of these toxins come from things that you use or consume every day. For example, food, water, beauty and personal care products. Your surrounding environment may also affect your health conditions.

With all the toxins accumulated in your body system, Rife frequency energy cannot pass through your cells and organs effectively. Therefore, we recommend running the Terrain Protocol Preset to prepare your body for Rife treatment programs.

For more details, please go to this link:
https://www.spooky2-mall.com/blog/why-is-terrain-protocol-the-first-step/

For how to run Terrain Protocol, please check this link：
https://www.spooky2-mall.com/blog/how-to-run-terrain-protocol-by/

Q8: Re length of program, I’ve seen it said it should not be longer than 4 hours in order to get more hits per day, is that correct?

A: Maybe you are confusing a chain, with a program sequence when run via remote. The guideline is that the remote program sequence should repeat within 4 hours at the MOST because pathogens may recover in that timeframe, so all benefits from running the frequency that did damage would be lost. It’s much more effective to limit the sequence to 2 hours so the repeats happen faster. But there is no limit of a chain of programs.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/posts/2184783011683590/

Q9: Can you use Spooky 2 with dental implants?

A: Some user said it is Okay:

” I have dental implants and I have run the full terrain without any problem.”

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1694989247329638/

Q10: My biofeedback takes 58 minutes on my GenX Pro, and I purchased a more powerful laptop hoping it would be faster, but it didn’t make any difference. What determines the speed of the biofeedback?

A: For the GenX Pro, Set the Min Read Time to smaller value that the default .07. Setting it to 0.043 will get you a 12 minutes scan, 0.22 will get about a 7 minute scan. You can set it to 0 for an even faster scan.

More information here:
https://www.facebook.com/groups/spooky2/posts/2685897834905436/

Q11: Which one was the one Rife used to treat cancer??

A: Spooky2 central GeneratorX Pro kit with phanotron tube and Straight plasma tube. With Spooky2 GeneratorX Pro, you can do fast biofeedback scan 2-3 times a week, and found the frequencies your body needs, then run the frequencies using Spooky2 central. Meanwhile you can run detoxing program, organ support, and system healing using Remote mode. Since Spooky2 central is very powerful in killing cancer cells and other pathogens, and Spooky2 remote is very gentle in healing your body. Straight plasma tube is very good for full body treatment, and phanotron tube is perfect for local target treatment.

For more, please check the link:
https://www.spooky2support.com/hc/en-us/articles/20371841158427-What-do-you-recommend-for-cancer-treatment

Q12: Why does the frequencies displayed on the generator not match those that displayed in the software?

A: This is down to the WCM (wave cycle multiplier), check the WCM multiplier found under the settings tab, for the waveform type you’re using. You should find that the frequency shown on the display of the GX is the correct multiple of the WCM value.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/?post_id=1692617030900193

Q13: How to delete a custom program?

A: Please watch this video:
https://www.youtube.com/watch?v=IoIhD-7I8qk

For more information about operation on your custom program, please read this blog:
https://www.spooky2-mall.com/blog/guide-on-creating-your-own-programs-and-presets/

Source: https://www.facebook.com/groups/spooky2/posts/2718103811684838/

Q14: I don’t have the Spooky2 Central, so can I run phanatron tube off of my GenX Pro?

A: 1. You MUST have a Central or Plasma unit to connect the plasma bulb to, as the unit connects between the generator and the bulb to amplify the signal from the generator to power the bulb.

The whole system is computer, generator, Central or Plasma, bulb. Of course, there are power and signal connections as well.

2. GeneratorX can’t run plasma tube directly; you need Spooky2 central or plasma unit too.

According to your description, you can start with Spooky2 GeneratorX essential kit firstly. It includes GeneratorX, remote mode, contact mode, PEMF coil, and cold laser. You can use them to do an advanced scan to find a suitable frequency to do the treatment.

In the future, you can add Spooky2 plasma too. Please check this link for details: https://www.spooky2-mall.com/product/spooky2-generatorx-essential-kit/

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1366055043556395/

Q15: I was running a Remote Terrain Detox programme on my Gen X pro but then I had a power cut. How do you start the Terrain programme again from where it was when power was lost. It does not show on the screen on the Generator when it stopped.

A: Get a UPS (Uninterruptible Power Supply), they have them at Amazon. This will give you 15 minutes to cleanly shutdown your Spooky system when the power goes out. When the power comes back on, turn on the generator, then the computer, the start Spooky. If the generator number is still the same as before the power went out, you can use the Resume button (to the right of the Start button) to continue where things left off.

More information here:
https://www.facebook.com/groups/spooky2/posts/2684266708401882/