Q1: I did a BFB with my Gen X pro, but how do I use it after I did the BFB?

A: After you finish the BFB scan and get the results, you can check the link to know how to do with the results:
https://www.spooky2-mall.com/blog/what-to-do-with-spooky2-biofeedback-scan-results/

Q2: How often to change the tens pads?

A: The tens pads can be reused for about 20 times. You can use it until TENS pads are not sticky. After each use, you can stick them onto the plastic sheet that they originally came with.

2. They will last as long as you can keep them sticky. Over time they will either pick up too much residue and/or dry out. Keeping them stored in the bags when not in use will prolong life. You can gently rinse the sticky side with water and let dry for a day, while stuck to the plastic storage square, to remove excess dead skin, etc. This will prolong their life once they start to lose their stick. It has also been reported that you can use an essential oil to keep the sticky side hydrated and clean prolonging life.

For more information please check this link:
https://www.facebook.com/groups/spooky2/permalink/757258204436085

Q3: Can you put the cold laser on either wrist?

A: Yes, it doesn’t matter which arm.

Q4: I’ve also seen people talking about the PEMF coil for charging/imprinting water, if doing so, approximately how long does it take?

A: Yes, you can imprint frequencies into water using Spooky2 PEMF coil, there’s a hole in the middle of Spooky2 Coil is that it gives the ability to implant frequencies into liquids. The hole is the right size for vials (small glass containers) to slide in. The idea is that people put medicine, tinctures, or even water, into a test tube or small container and place it in the coil which is resting flat on a table. They then run treatment frequencies on the contents of the bottle. After a while they stop the generator and drink the contents of the bottle.

For more details about imprinting, please check the link:
https://www.spooky2-mall.com/blog/easy-spooky2-frequency-imprinting/

Q5: Can you use PEMF coil on your head for headache or neck pain?

A: Yes, you can sue the coil on your head.

Q6: Can you use a toenail instead of a fingernail?

A: You can use a toenail if you wish. We recommend fingernails because they’re not as thick, so they’re more flexible. You may have to cut the toenail into segments and just use one segment in the Remote. This is OK.

Q7: If a preset program specifically states to use the high power port, will using the colloidal port instead diminish the effectiveness of the treatment?

A: Yes. When you use the CS port vs. the High Power Contact port, the difference physically, as commented above, is that there is a 10k Ohm resistor inline with the CS port.

What this does is limits current flow.

When you use frequencies that are over 10kHz on either port, you won’t usually feel anything as there is no resonance with your nervous system.

The reason you feel the lower frequencies is that it resonates with your nerves and causes the muscles to fire.

Typically use the CS port if you are running low frequencies and felt too much even with the contact settings in effect to reduce the likely hood of feeling too much (Reduce Amp, Amp Ramp, etc.).

Now for the other main difference between the two.

The High Power Contact port allows higher harmonic frequencies to be passed into the body. The 10k Ohm resistor that limits current in the CS port also filters these very high harmonics out.

The CS port was initially created to limit current to provide a better Colloidal Silver creation process. The side effect is that it also provides a very safe contact session as you can not get too much current in this mode.

However, some devices like PEMF would not benefit from limited current, so the High Power contact port was then added in the Boost 3.0.

Q8: Can we use spooky 2 on kids, from what age?

A: Yes, you can use Spooky2 on kid, but we suggest better use it for kids over 7 seven years old.

For more details, you can check the QA:
https://www.spooky2support.com/hc/en-us/articles/224024908-What-s-the-youngest-age-of-children-you-could-use-the-remote-setting-on

Q9: If you choose a frequency that the body doesn’t need, is that detrimental, or is it simply a “neutral” situation?

A: No dear. If a frequency does not resonate then nothing happens. So you do not need to worry about it.

It will not harm our bodies, but if it runs at an inappropriate frequency, it may make us feel uncomfortable. We still recommend that you run the frequency you need.

Source: https://www.facebook.com/groups/spooky2/permalink/2814308515397700/

Q10: Can Terrain be run monthly or would that be too much?

A: Yes, you can run it monthly. If you are in good health, it shouldn’t hurt to run it for a year, but I don’ think it is necessary. I think its probably better to run it periodically (say once a month) rather than continuously, as your body can become accustomed to it.

Q11: What is the difference between a grade scan and a biofeedback scan?

A: A grade scan is when you want to find out what frequencies are best for a specific person when there are too many to run at once. Of course, one needs to know what pathogen they are fighting to choose programs to begin with.

With the GX scan that works in 6 or so minutes, the Grade Program scan is much less important, in my opinion, but not everyone has that generator.

For more details, please check:
https://www.facebook.com/groups/spooky2/permalink/956417251186845/

Q12: Because I don’ t see lights on the remote, I’ m always wondering if the remote/generator is still working. I don’ t want to check with the free generator port for fear of screwing up the whole programs…

A: Four factors determine how the LEDs respond to the signal: frequency, waveform, offset, and amplitude.

For more, please check the link:
https://www.spooky2support.com/hc/en-us/articles/115003973173-Why-does-my-Remote-light-flash-but-sometimes-doesn-t-light-on

Q13: Which part of your body do you place the tens pad when doing BFB in contact mode?

A: For the whole body scan, you can put the tens pads right wrist to the left ankle.

For some problem area scan, please put the tens pads between the area and put the two tens pads as near as possible.

For more details, please check the video:
https://www.youtube.com/watch?v=ArxDJO3eyq8

Q14: Is there any way to test if our coil is working?

A: Yes, please check the link:
https://www.spooky2support.com/hc/en-us/articles/218398328-How-to-test-whether-Spooky2-PEMF-coil-is-working

Q15: Can I do remote frequencies on more than one patient at a time?

A: Yes, you can do that. The fingernails can be put in one remote together as long as you’re going to run the same programs for them, but we recommend keeping them separate with different paper stickers. Please be kindly noted that it’s not suggested putting human’s and animals’ DNA sample in one remote. And it’s better not to put your DNA sample with people who have serious illness in the same remote.