Q1: My CS color is clear, not grey or tinted color. Is it okay? What would affect the color of colloidal silver?

A: When it comes to colloidal solutions, the main parameters contributing to color change(plasmon) likely come down to particle type, size and density. Of which I’d add, the type parameter depends on whether one chooses to qualify ions as particles or not.

That said, out of all of the references, I’d consider the first paragraph to be the most complete under general guidelines. Whereas the other statements appear to support this by way of deductive chemistry. However, I’d also add that it may not always be feasible to apply observations from one generator to another given the inherent difference in process methods that exist between them. Which will undoubtedly affect the ionic to particulate balance for example. – NB. ions possess no tyndall or light scattering properties, in contrast to silver compounds etc.

Hope this helps.

1. every parameter(voltage, temp, water, etc) will have an impacts on solution composition. ionic/particulate ratio, compound types, size, saturation limit and-so on and so-forth.

For more details, please check the link:
http://www.spooky2.com/forums/viewtopic.php?f=6&t=4785

Q2: For what is it used in the eyes?

A: Apply colloidal silver on pink eye, conjunctivitis, sty, ear infection. For eye infection, use two drops in the eye, three to four times a day. For ear infection, use 10 drops in the ear, leave for two minutes, then tip it out and repeat three to four times a day.

Q3: How do you know if your colloidal silver (made with spooky 2) is successful?

A: The only test I know of for CS (without sending it to a qualified lab for big bucks) is to shine a laser pointer through it and see the line pass through the liquid… The stronger the line, the stronger the silver content. Obviously, this test is not a quantifiable measurement of the content, just a visual representation of the particles within.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/683550638473509/

Q4: How long will the colloidal silver be fresh after production?

A: Shelf life of about a year or more. Glass, preferably dark container would be recommended.

Q5: What is the Alternative to magnetic stirrer for making Colloidal Silver?

A: Using a small aquarium air pump attached to a bubbler stone.

The same item “Fusion Air Pump 200 Aquarium Air Pump” is also available from Amazon.

A small motor to rotate the water container around the rods, works wonderfully, and scrubs the rods with water continuously.

For more details, please check:
http://www.spooky2.com/forums/viewtopic.php?f=28&t=4674

Q6: How can we run terrain in sequence on the generator stand alone?

A: You need to load the terrain protocol into the generator and run them standalone, for more details, you can check this blog:
https://www.spooky2-mall.com/blog/how-to-load-and-run-terrain-protocol-using-generatorx/

Q7: What container should we use to store colloidal silver?

A: Use Dark glass because light will deteriorate it pretty quickly.

No metal and not mixing it with salt.

I use a glass bottle wrapped in tinfoil to keep out light, works fine.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/766319810196591/
https://www.facebook.com/groups/spooky2/permalink/1568706126624618/

Q8: If demineralize water is good enough for making colloidal silver or it has to be distilled water?

A: Non-spooky CS generators users have read that demineralized water is good. It is suppose to give a reading of 0 ppm prior to making CS.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/683897608438812/

Q9: To make colloidal silver, do I put one or two magnetic stirrers inside the glass container?

A: Just one. The other is probably a spare in case you lose one.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1694458044049425/

Q10: How much time would GeneratorX(GX) take to make colloidal silver with 1 liter of distilled water?

A: Mine takes 25 hours for 1ltr using an XM.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/1539626769532554/

Q11: Can I make Colloidal Silver while I am using both remotes on GeneratorX?

A: Yes, you can make colloidal silver while you are using remotes on GeneratorX. Please use another generator to make colloidal silver.

For more details, please check the link from:
https://www.spooky2.com/forums/viewtopic.php?f=83&t=10465

Q12: What would affect the color of colloidal silver?

A: When it comes to colloidal solutions, the main parameters contributing to color change(plasmon) likely come down to particle type, size and density. Of which I’d add, the type parameter depends on whether one chooses to qualify ions as particles or not.

That said, out of all of the references, I’d consider the first paragraph to be the most complete under general guidelines. Whereas the other statements appear to support this by way of deductive chemistry. However, I’d also add that it may not always be feasible to apply observations from one generator to another given the inherent difference in process methods that exist between them. Which will undoubtedly affect the ionic to particulate balance for example. – NB. ions possess no tyndall or light scattering properties, in contrast to silver compounds etc.

Hope this helps.

PS. every parameter(voltage, temp, water, etc) will have an impacts on solution composition. ionic/particulate ratio, compound types, size, saturation limit and-so on and so-forth.

For more details, please check the link:
http://www.spooky2.com/forums/viewtopic.php?f=6&t=4785