Q1: Why do I get different results every time I use the sample digitizer? Some days I get multiple hits and some I get nothing.

A: This is a complex question, and there are a number of reasons why it happens. First is the nature of the terrain you’ re scanning – your body.

For more, please check the QA:
https://spooky2scalar.zendesk.com/hc/en-us/articles/26549428491931-Why-Do-Scan-Results-Differ-Each-Time

Q2: Is scalar biofeedback more accurate than sample digitizer using your own blood?

A: No, The Sample Digitizer is good for killing pathogens in a sample, but if your pathogen is not in the sample but in your body, the TENS will work better. Also, there is no way to do biofeedback using the Remote and GX (Although you can use Spooky2 Pulse and the Remote, you are still wired to the computer).

Spooky2 Scalar Biofeedback scans are special. The Spooky2 Scalar Digitizer measures tiny changes to the scalar field around you during scalar frequency scans. Frequencies that invoke changes to the scalar field will be recorded. These changes indicate subtle scalar reactions within your body. When you are doing a Scalar Biofeedback scan, only one GX is required since it has two generators in one. Generator 2 modulates the scalar field, and Generator 1 measures the response.

It is best to lie perfectly still when doing a Scalar Biofeedback scan and make sure that you only have one person in the scalar field. To ensure the accuracy of your scan result, please also keep your pets away during the scan.

For more about how to get the most accurate biofeedback results, please check the QA:
https://www.spooky2support.com/hc/en-us/articles/360050937014-How-do-you-get-the-most-accurate-biofeedback-results

Q3: So what is the purpose to do the reverse look up if what it comes out is crazy , specially if one uses the  Add harmonics ? It is helpful and how.

A: I will show you some links which may help your questions:
https://www.spooky2support.com/hc/en-us/articles/219876767-What-is-reverse-lookup
https://www.spooky2support.com/hc/en-us/articles/216698208-Harmonics

Q4: Can you use this scalar bfb method with a knee replacement?

A: Yes, you can. But It is not recommended for people having pacemakers to use Spooky2 Scalar. No electrical or electronic device is recommended to be used around someone with a pacemaker.

Q5: Do you need to take off rings and any jewlery for a Scalar BFB scan?

A: The scalar field is unaffected by the metal, only the link cable and scalar unit can be affected by the metal. The metal within the body has no effect on the scalar field, it won’t interfer with the scalar field.

The jewelry is fine and it is ok to leave on during the treatment.

It does not affect the field, or the effect is so small to make it negligible.

Q6: Will the bio feedback “tell” me if all the pathogens have been destroyed ?

A: Biofeedback scan requires a frequency sweep to be input to the body, plus a system to monitor the results of this. As this sweep is being transmitted, it will kill or injure pathogens. Your body registers these events as stresses, and each one is recorded. It aims to find the most suitable frequencies for your body, giving your body the best-needed treatment.

Scan reports frequencies only.

You can do a Reverse Lookup to get name of pathogens/ diseases that correlate what your frequency hits.

Reverse Lookup will show the programs that the frequencies (or their harmonics) show up in. The programs may or may not be why the frequency shows up in your scan.

For more details, please check the link:
https://www.facebook.com/groups/spooky2/permalink/797074960454409/

Q7: How far would the “field” extend? around the subject

A: Please check the link:
https://spooky2scalar.zendesk.com/hc/en-us/articles/9774407484059-The-questions-about-the-dimension-of-the-scalar-field

Q8: If on massage table can you put boxes head to toe? Or is it better side to side?

A: Yes, you can place the boxes head to toe.

The minimum recommended distance between the two units is 6 feet. Try to keep at least 2 feet away from the Transmitter and 1 foot away from the Receiver. The further the two boxes can be apart from each other, the bigger / stronger the field will be as well. 

Q9: Did you say slave to G2? And master to G1?

A: Please check the video:
https://www.youtube.com/watch?v=sY7UA5kt7qY

Q10: Can you tell a little bit about BASELINE?

A: The Baseline Before BFB button on the GenX Pro is used to establish a clean reference signal before performing a biofeedback scan. It helps eliminate environmental electrical noise, ensuring that only meaningful responses from your body or sample are detected during the scan.

When you run a Baseline scan, the system records background noise without any sample. This allows Spooky2 to ignore disturbances like Wi-Fi signals and electrical interference, improving scan accuracy. Once the Baseline is complete, you can proceed with your biofeedback scan as usual.

For more details, please click here:
https://www.spooky2-mall.com/blog/maximizing-biofeedback-accuracy-with-spooky2s-baseline/

Q11: Can I perform other biofeedback scans in scalar field? Why can I do biofeedback scan using Scalar Digitizer?

A: No, you cannot perform other biofeedback scans whilst in scalar field, since they use different detecting way and the field will affect the scan results. For example, Spooky2 Pulse detects your heart beats, which would be affected by the scalar field. However, Spooky2 Scalar Digitizer measures tiny changes to the scalar field during scalar frequency scans, while GeneratorX records how the electrical signal behaves, so only Scalar Digitizer can do biofeedback scan in Scalar field.

Q12: What to do with Spooky2 Scalar BFB scan results?

A: After you complete a scan, you will get a list of frequencies that show up as your results. These can be saved in a “BFB” program that you can run through the scalar unit. Select scalar shell preset, click on program tab and select your BFB program. Click on control tab, check overwrite box, click on your generator number to run the results on the scalar unit.

This video will show you how to run your scan results: 
https://www.youtube.com/watch?v=NC12pLO-vBA

Q13: Where can I put the DNA sample whilst doing scalar biofeedback scan?

A: Scalar Digitizer is different from Sample Digitizer, you don’t need to have your DNA on it and you just need to lie between two Scalar boxes. You just need to lie between two Scalar boxes.

For more details, please check the link:
https://www.facebook.com/groups/spooky2scalar/permalink/361156994457865/